What are the installation techniques when installing electric doors?
I. Construction instructions for electric door companies
Before installation, you should go to the construction site to find out whether the site conditions meet the construction requirements. For example: the power supply must be delivered and the ground is level. All construction conditions are met before construction can begin.
Measure the size of the door opening, discuss the production requirements with Party A, and then produce the construction drawings according to the requirements and submit to Party A for approval.
Except for making the frame and door leaf (including skeleton, stainless steel, glass, etc.) according to the drawings.
After all the preliminary works are completed, installation and construction can be carried out.
Second, start to install the door machine
For wall installation, the wall surface must be leveled before installation to avoid unevenness caused by rail bending and noise. The flatness of the rail mounting surface should be less than 1.5MM. For wall mounting, the rail can be drilled and fixed with expansion screws.
Channel steel and angle iron frame can be fixed directly with flat head screws or self-tapping screws, and the interval can be the same as above.
Before installing the track, first use a transparent water pipe filled with water (not included in the pipe) to measure the level of the two ends of the guide rail and the middle, and the ground shall prevail.
Drill the screw holes of the guide rail, and then temporarily fix the two ends of the guide rail with a screw to the wall or steel structure. After correcting the level again, confirm the accuracy and then increase the fixing. Note: Generally, the guide rail is lifted by the door to 25MM. (Depending on the model)
The sensor should be installed a little outside first, usually above the center of the door opening. The height depends on the site conditions. Refer to the manual before wiring.
Before installing the electric parts, clean the guide rails, and then install the motor, electric panel, tail wheel, and transformer in the track fixing grooves, move it to an appropriate position, and install and fix the fixing screws.
Third, install the door leaf
Assemble the movable door body, measure whether the upper and lower sides are equal between the movable door body and the fixed door body after the door body is installed, then push the door to align with the fixed door, and then attach the belt and the stop plate.
Adjustment check. All the above steps are completed, and the installation of the electric door is roughly completed. If it is not satisfactory, you can adjust it as needed.
4. The test controller can be adjusted as required, but the machine must be very sensitive when adjusting, and you can press it lightly (for specific adjustment, follow the instructions on the electric panel). If everything is normal, seal the case cover and install the inner sensor. The device is done.
After the electric door is put into use, in the initial stage, there will be a period of running-in to correct the error caused by the operation.
A very few customers will change the door leaf after a certain period of operation to give people a refreshing feeling. One thing to note is that the weight of the door leaf must be strictly restricted and cannot exceed the rated load of the electric door machine.
The electric door without safety light must stop people from staying in the non-sensing range to avoid a pinch event.
The service life of electric door electrical components is mainly related to improper use and accidents; the consumable parts under normal use conditions of electric doors are guide rails, transmission belts and pulleys. The dynamic wear of pulleys does not only refer to the wear of the pulleys on the guide rails at a constant speed. More importantly, it refers to the wear and tear of the automatic translation door in a short distance back and forth acceleration motion.
Generally, the electric door must be fully cleaned and adjusted within three months and up to one year.
First of all, the false fault of the induction electric door (taking sliding door as an example) refers to the failure phenomenon caused by external factors, not the failure of the unit components. If it is a false fault, you can easily repair it yourself. Of course, if it is determined that there is a problem with the electrical or mechanical equipment inside the host, then we still recommend that you contact us and we will troubleshoot and replace the accessories for you. There are special accessories from various manufacturers, and most of them are not compatible.
- Previous: What are the working principles and precautions of access control card readers? 2015/8/6
- Next: How to choose ESD static detection access control system? 2015/8/6