How to install smart three roller gate access control
The installation of the three-roller gate plays a vital role in the use and life of the three-roller gate. It also plays a very important role in whether the user can pass the passage quickly and effectively and the personal safety of the user.
How to properly install the three-roller brake should pay attention to the following issues:
1. Formulate a reasonable and feasible construction plan
Before installation, communicate with the customer in a timely and complete manner to understand the on-site environment and determine the plan:
1) Make a plan according to the environmental conditions on site. Whether the installation site is used in the open air or indoor space, if it is used in the open air, you need to wear a waterproof box three roller brake to prevent the circuit board from being corroded by cloudy weather; the choice of the waterproof box material is different depending on the working environment. In the north, an iron waterproof box and a temperature control system should be used, and in the south, a rubber waterproof box and a diffuse temperature system should be used.
2) According to the width and length of the on-site passage, determine the number and shape of the three-roller gates. For example, whether to choose a vertical three-roller gate or a bridge-type three-roller gate. Dimensions of the vertical three-roller gate: 420x330x980 (mm). Roller gate dimensions: 1200x280x1000 (mm), the size of the three-roller lever to the chassis is 510mm, that is, the area of the vertical three-roller gate is 420x (330 + 510), and the area of the bridge-type three-roller gate is 1200x (280 + 510) ), Fully consider the gap between the gate and the lever when determining the selection (the gap between the gate and the chassis is generally 50mm), the floor area and placement of each three-roller gate,
3) According to the distance between the main control computer and the three roller gates, select the wiring method (whether the line is open or dark) and the communication method of the controller (the distance between the general computer and the three roller gates is less than 800 meters. We recommend 485. Communication, the distance is more than 800 meters, we choose TCP network communication.
Second, make preparations before installation
Generally, two 6 to 8 minute plastic pipes are slotted and embedded in the site according to the actual size of the three-roller gate before installation. A 50-100mm gap is left between the gate and the gate to facilitate opening the top cover and adjusting the machine. , Easy maintenance, etc., the gate and the gate are embedded, one hose goes through the power line (strong current), the other hose goes through the signal line (weak current), the power line and the signal line cannot go through the same hose at the same time. It will cause bad communication effect and safety hazard. The embedded pipe should be 30-40mm high above the ground. The line vertical three-roller gate should be in the middle and bottom of the machine. The bridge three-roller gate should be on both sides. The middle bottom of the three-roller gate is closed. It is not convenient for maintenance and hidden safety hazards when the line pipe is buried in it. Generally, the power cord has an aging period and should be repaired once a year).
Third, fixed adjustment
The bottom of the fixing is fixed with 4-M10x100 expansion screws, which cannot be swayed. The overall appearance of the machine is the same. (It is best to use a thin line to draw a straight line before the fixation. The vertical and horizontal directions are consistent.) The three roller gates and the three roller gates are connected in series, one by one. Adjust until it works. The three-roller gate should be placed horizontally with the ground, so that the effect and the life of the three-roller gate can be in the best state.
Fourth, after installation, check whether the chassis is grounded.
According to what our company has seen in the past, many customers have not effectively connected the bottom line after installation. The shell of the three-roller brake is mostly made of stainless steel. If the shell is not grounded, it will cause a great safety hazard to the user.
Anhui Secco Intelligent Technology Co., Ltd. registered in 2002 with industrial and commercial registration. In 2005, it successfully registered trademarks such as "Secco" and "SAYOK" with the State Trademark Office. Welcome to inquire and order Anhui Hefei Three Roller Gate, Hefei Swing Gate, Hefei Wing Gate, Hefei Translation Wing Gate, Hefei Full Height Turnstile, Hefei Bank Full Height Turnstile, Hefei Prison Full Height Turnstile, Hefei Prison Three Roller Sluice, Hefei Swing Gate, Hefei electric swing gate, Hefei supermarket swing gate, Hefei car swing gate, Hefei pedestrian swing gate, Hefei non-standard swing gate, Hefei wing gate, Hefei examination center wing gate, Hefei one-line gate, Hefei pedestrian / vehicle swing gate, Hefei Blocking gates, Hefei smart gates, Hefei smart gates credit card system, Hefei gates credit card system, Hefei community access control system, Hefei community access control management system, integrated electronic tickets, credit card, access control attendance, fingerprint, palm print, face, iris Integrated use of access control systems such as identification, order hotlines: 13637922220, 13637922221, sales manager Zhang